How To Manage My On Demand Feature

How To Manage My On Demand Feature

Need eyes on your spot right now? On Demand lets you request a fresh photo or video from the Moultrie App any time. You don’t have to wait for the next check-in or drive out to the stand.

On Demand works in the Moultrie App only, not on the website. Features differ by model, so check your settings for your camera.

There’s no fee to request an On Demand photo or video. Each request you upload counts against your monthly picture balance. One On Demand photo counts as 6 standard photos. One On Demand video counts as 1 standard video.

Which setup do you have?

EDGE 3, EDGE 4, and EDGE 4 Pro with the latest firmware. You can set a schedule so On Demand is ready only during the hours you check your camera. That saves battery. Use the first set of steps below.

Every other camera. You get an on/off switch. Use the second set of steps below.

If you don’t see Daylight Hours in your settings, your camera hasn’t updated yet or doesn’t have the feature.

Set up On Demand on EDGE 3, EDGE 4, and EDGE 4 Pro

You have three settings:

  • Off. On Demand is turned off.
  • Daylight Hours. On Demand is ready only during the window you set. The default is 6am to 7pm. You can slide it to any window between 5am and 8pm, in steps of 15 minutes. This setting saves battery.
  • Always On. On Demand is ready around the clock.
  • Tap Devices, then tap your camera.
  • Tap On Demand.
  • Choose Off, Daylight Hours, or Always On.
  • If you chose Daylight Hours, drag the slider to set your start and end times.
  • Tap Save Settings. The button turns on once you change something. If you tap the back arrow before saving, the app asks “Leave without saving?” Tap Stay to keep editing or Leave to discard your changes.
  • Your camera needs to connect to pick up the new setting. Until it does, you’ll see a Pending Check-In alert and a banner above your camera.
  • Once your camera has connected, tap the On Demand button and choose Photo or Video.
  • Your request should upload within 4 minutes.

 

What you’ll see after you save

  • Inside your window, the On Demand tile shows your schedule and Status: Ready.
  • Outside your window, the On Demand controls are disabled and the status reads Not Ready. Your window opens again at your start time.
  • The window follows your camera’s local time, based on its GPS location or where it is pinned on the in-app map.

Already using On Demand? Your setting carries over after the update. If On Demand was on, it becomes Always On and works the same as before. If it was off, it stays Off. No action is needed.

Use On Demand from your feeder

If a Connected Feeder is linked to your camera, Feed On Demand follows the camera’s On Demand schedule. One window covers both.

  1. Tap Devices, then tap your feeder.
  2. Find Feed On Demand. The status shows the hours it’s ready.
  3. Tap Feed Now to run the feeder, or tap Feed On Demand to open its settings.
  4. To change the window, tap Manage On Demand. It opens the On Demand settings for your linked camera.

Outside the camera’s window, Feed On Demand reads Not Ready. Tap Manage On Demand to change the hours.

Set up On Demand on other cameras

On Demand has to be turned on before you can make a request.

  1. Tap Devices, then tap the Gear icon next to your camera.
  2. Tap On Demand, turn the feature ON, and tap Save Settings.
  3. Your camera needs to connect to pick up the setting. Until it does, you’ll see a Pending Check-In alert and a banner above your camera.
  4. Once your camera has connected, your On Demand status updates to Ready.
  5. Tap the On Demand bubble, then choose Photo or Video.
  6. Your request should upload within 4 minutes.
On Demand 1.jpg
On Demand P.jpg
On Demand P1.jpg

Frequently asked questions

What does On Demand do?

It lets you request photos and videos in real time. The setting has to be on, and your camera has to accept it first.

How do I turn On Demand on?

Open On Demand in the app. On EDGE 3, EDGE 4, and EDGE 4 Pro, choose Daylight Hours or Always On. On other cameras, turn the setting on.

When can I start making requests?

After your camera connects and accepts the setting. From then on, you can request any time On Demand is ready. On Daylight Hours, that means any time inside your window.

What does Not Ready mean?

You’re on Daylight Hours and it’s outside your window. The controls stay disabled until your window opens again. You can change your window in the On Demand settings.

What time zone does my window use?

Your camera’s local time, based on its GPS location or where it’s pinned on the in-app map.

Which cameras have Daylight Hours?

EDGE 3, EDGE 4, and EDGE 4 Pro cameras updated to the latest firmware. Other cameras keep the on/off switch.

I updated my camera. Do I need to change my setting?

No. If On Demand was on, it’s now Always On. If it was off, it’s still Off.

Why does Feed On Demand say Not Ready?

Your feeder follows your camera’s schedule. When the camera is outside its window, the feeder is too. Tap Manage On Demand to change the hours.

What can I request?

High resolution photos and videos from the Moultrie App.

Can I use On Demand if the power is off?

No. The camera must be on.

How long are the videos?

Your current video length setting decides it: 5, 10, 15, or 20 seconds.

How fast will my photo or video show up?

Up to 4 minutes, depending on video length and signal.

How does On Demand affect battery life?

It uses more battery when it’s on. If you’re not using it, turn it off. On EDGE 3, EDGE 4, and EDGE 4 Pro, Daylight Hours keeps your camera from waiting on requests overnight. If you make a lot of requests, a solar panel helps keep the power up.

Was this article helpful?

219 out of 351 found this helpful